« BACK  

ROEX Extruder Generation - maximum energy efficiency

ROEX Extruder Generation
ROEX Extruder Generation

Rosendahl is the technology leader in the area of extrusion lines for years. One of the biggest milestones on the way towards this aim was the continuous improvement which led to the ROEX Extruder generation.

To achieve a reduction of the power consumption Rosendahl was focussed at the extruder unit (the main consumer of energy in an extrusion line) and developed measures to enhance the energy efficiency of the new Rosendahl Extruder Generation ROEX.

The following improvements were made:

  • The drive has been modified from DC technology to state of the art A/C power technology. Additionally the thyristor rectifier which caused enormous wastage due to reactive power was omitted.
  • By converting to a direct screw drive by means of a planetary gear motor mechanical losses were reduced. The planetary gear is directly driven by four symmetrically aligned motors ("Compact Motor & Gearbox Design").
  • Thanks to an optimized processing unit (screw & feeding section) the material output could be massively increased. At the same time energy consumption decreased.
  • During the development of the new Extruder Generation ROEX special attention was paid to additional electrical power consumers like the heating and cooling section. A new design of the heating elements in combination with the cooling channels and the fans allowed substantially faster reactions of the extruder temperature control.

The effect of this was not only a precise control but also a reduction of the power consumption of the heating and cooling section.

Needless to say, further machines of the Rosendahl extrusion lines were subjected to measures to increase efficiency. It is of great importance to Rosendahl that the latest technologies are constantly applied (e.g. use of more efficient electronic components like AC motors, illuminants, conflation of several PLC systems, regulators and relays,...).

Furthermore Rosendahl uses a high level line control system. This line control coordinates the processes of all machines and demands only the power which is required for each particular process.

Rosendahl's ROEX extruder generation saves compared to conventional production lines from 15 to 25% energy for the entire production line with a comparable productive capacity!

PUBLISHED: 07 May 13 Bookmark and Share
Company:
Rosendahl Nextrom GmbH
Visit Rosendahl Nextrom GmbHs website
Country:
Austria
Tel:
+43 3113 5100-0
Fax:
+43 3113 5100-59
Email:
office.austria@rosendahlnextrom.com
Website:
www.rosendahlnextrom.com
Other News from Rosendahl Nextrom GmbH:

»
Extreme conditions require excellent cables
»
PEEK extrusion line
»
Rosendahl silicone extrusion line
»
Rosendahl Nextrom at wire Russia 2015
»
Rosendahl Nextrom opens new technology center in Pischelsdorf
»
High performance X-ETFE extrusion
»
Rosendahl & Nextrom at Interwire 2015
»
Rosendahl & Nextrom - wire China 2014 Preview
»
Loose Tube news: A new era just began
»
ROEX Extruder Generation - maximum energy efficiency
»
Successful Interwire for Rosendahl
»
Rosendahl & Nextrom at wire Russia 2013
»
Rosendahl's new FOC multipass cooling trough for loose tube lines
»
Rosendahl and Nextron at Interwire 2013
»
Finished power cables by merging power SZ with sheathing
»
RX5 completes Rosendahl’s crosshead series RX, fit for single crosshead sales
»
Pushing the limits with the RX 25T for foamed RF Cable from Rosendahl
»
Payoff and take-up
»
Crosshead developments
»
Merging SZ with sheathing
»
Rosendahl - wire 2010 preview
»
Finished cables on one line
»
Intercable 2009
»
Advanced crosshead technology
»
Intercable Meeting Austria 2009
»
Crosshead developments
»
50 Years Innovation from Rosendahl
»
Rosendahl celebrates fifty years in the industry
»
“Most successful show in the group’s history!”
»
Efficient screening with SZ-technology
»
Solutions from Rosendahl and Nextrom


Industry News:
David Lee will fully retire from Metalube in August 2018
Metalube bids farewell to David Lee
Metalube Limited, UK
Wire cleaned for decorative finish by PWC system
Wire green cleaning for plating and a decorative glossy finish
Decalub, France
Klaus Lenz - CEO of Ungerer Technology GmbH
Klaus LENZ has been appointed as the CEO of UNGERER Technology GmbH
Ungerer Technology GmbH, Germany
The cover page of
Digitized wire & cable manufacturing - The "NIEHOFF Magazine" 1/2018 is out now
Maschinenfabrik Niehoff GmbH & Co KG, Germany
Magnet assemblies can now be fabricated quickly and efficiently using a robot
Robot for magnet assemblies
Goudsmit Magnetics Group, Netherlands
From top: Multiwire drawing line type MMH 121 + RM 161; D 632 type double twist bunching machine; NPS double spooler type SV 402 D; 
Rotary braiding machine BMV 16 ; Rotary braiding machine BMV 16 (interior)
Digitization - Niehoff at wire 2018
Maschinenfabrik Niehoff GmbH & Co KG, Germany
The Strand Compaction Units are available for 2mm to 40mm strand diameters
Rope strand compaction gives Bar Products & Services a first quarter boost
Bar Products & Services Ltd, UK
Ridgway are manufacturers of precision taping and winding machines for the electrical and energy industries
Ridgway Machines moving forward and expanding
Ridgway Machines Ltd, UK
Wire & Plastic Machinery booth from Wire Expo 2016
Wire and Plastic Machinery at Wire Expo 2018
Wire & Plastic Machinery Corp, USA
Domino (Wiedenbach) will be showcasing intelligent coding and marking solutions at wire 2018 in Düsseldorf, Hall 12, Stand 12E72
Industrial coding and marking solutions for demanding production environments
Wiedenbach Apparatebau GmbH, Germany
» VIEW ALL NEWS «